Timing in bowling is how your arm swing lines up with your footwork. You’re on time when the ball reaches the bottom of the swing, at the release point, just as your sliding foot finishes its slide. You’re early when the ball gets there before your feet do. You’re late when your feet finish first and the ball is still on its way down. Good timing makes a strong, repeatable release possible, and poor timing is behind many accuracy and power problems.
Directions assume a right-handed bowler using a four-step approach. Left-handers can mirror them.
What Timing Means in Bowling
In a four-step approach, each step lines up with a stage of the swing:
- Step 1 (right foot): pushaway
- Step 2 (left foot): downswing
- Step 3 (right foot): backswing
- Step 4 (left foot slide): forward swing and release
Our guide to the four-step approach walks through each step. Timing is about whether the ball and feet stay matched through that sequence, especially at the end.
On-Time, Early and Late
| Timing | What happens | Common result |
|---|---|---|
| On time | Ball reaches the release point as the slide foot stops | Balanced finish, clean release |
| Early | Ball arrives before the slide is finished, so the arm is ahead of the feet | Loss of leverage, weak roll, muscled shots, often missed targets |
| Late | Feet finish before the ball arrives, so the arm lags | Pulled or forced shots, inconsistent release, and sometimes a lot of power if well controlled |
Checkpoints: How to Tell Where Your Timing Is
The easiest way to check timing is a side-on video, ideally in slow motion. Look at these moments:
- First step. Does the pushaway start with the first step? If the ball moves before your foot, you’re likely to be early. If it moves well after, you’re likely to be late.
- Third step (four-step approach). Is the ball at or near the top of the backswing as your right foot lands? If it’s already coming forward, you’re early. If it’s still on its way back, you may be late.
- The slide. Where is the ball when your slide foot starts to slide? Many coaches like to see the ball around the top of the backswing, or just starting down, at that moment.
- Release. Is the ball passing your ankle as the slide comes to a stop?
Early Timing
Signs
- You arrive at the foul line with the ball already swinging forward or past you.
- You feel like you have to “throw” the ball or hurry the release.
- The ball rolls weakly or hooks less than expected, because you can’t get your body behind it.
- Your finish is off balance, often falling to one side.
Common causes
- Pushing the ball away before your first step
- A pushaway that’s too high or too far out, which makes the swing take longer and pulls the ball ahead
- Feet that are too slow for your swing
- Muscling the backswing
Fixes
- Start the pushaway and first step together.
- Make the pushaway a little smaller or lower.
- Pick up your foot tempo slightly, or start a little farther back so your steps are longer. See how to bowl faster or slower.
- Some bowlers fix chronic early timing by switching to a five-step approach, which gives the feet a head start.
Late Timing
Signs
- Your slide foot stops and you’re waiting for the ball.
- You feel you have to pull the ball down and through with your arm.
- The ball often goes left (for a right-hander), or the release varies a lot.
- You may drop your shoulder or turn your body to make room.
Common causes
- Starting the ball after your first step has landed
- Rushing your feet, especially the last two steps
- A backswing that’s higher than your footwork can support
- Holding the ball lower than usual, then trying to speed up
Fixes
- Start the pushaway with your first step, or very slightly before it.
- Slow your feet slightly, especially the first two steps.
- Let the swing go back naturally rather than lifting it higher.
- If you’re rushing because you start too close to the foul line, move back slightly. Too far back can also make you rush, so experiment.
Is Slightly Late Timing Better?
Many coaches prefer timing that’s a touch late, where the ball is still near the top of the backswing as the slide begins. Their reasoning is that it gets your body into a strong, low position before the ball comes down, which can add leverage and revolutions. See our explainer on torque and rev rate.
The key word is slightly. Very late timing usually leads to pulled shots and an inconsistent release, and very early timing usually costs power and accuracy. Most bowlers should aim for timing that’s consistent first, then fine-tune with a coach.
Drills to Improve Timing
- Say it out loud. Walk the approach with the ball, saying “out, down, back, slide” so each word lands with a step.
- Pushaway and first step only. Practice starting the ball and the first step together, then stop. Repeat until it feels automatic.
- One-step drill. Start in the finish position with the ball held at the top of the backswing. Take one slide step and let the ball swing through. This teaches the feel of a ball arriving as the slide ends.
- No-ball walk-throughs. Walk the approach without a ball, swinging your arm as if holding one, to feel the rhythm.
- Video and compare. Record several shots from the side and compare each checkpoint.
A coach can often spot timing issues in a few shots. See USBC coaching and the Specto system.
Timing and Other Problems
Timing problems often show up as other symptoms:
- Drift: an early or late ball can pull your body off line. See why you drift on your bowling approach.
- Missing your target: see how to use the arrows to target.
- A weak or inconsistent hook: see our guide to hooking a bowling ball.
FAQ
How do I know if my bowling timing is off?
The clearest way is a side-on video. Check that the pushaway starts with the first step and that the ball reaches the bottom of the swing as the slide foot stops.
What causes early timing in bowling?
Usually the pushaway starting before the first step, a pushaway that’s too big, or feet that are too slow for the swing.
Can timing be different in a five-step approach?
The principle is the same, since the ball should still arrive as the slide ends. The difference is that the pushaway happens on the second step instead of the first.