The arrows on a bowling lane are aiming marks. They sit roughly 15 feet past the foul line, and most bowlers aim at them instead of the pins, which are 60 feet away. A target 15 feet away is far easier to hit consistently, and if the ball rolls over the right arrow from the right starting spot, it heads for the pocket.
This guide explains how the arrows are laid out, which one to aim for, and how to use them to adjust. Directions assume a right-handed bowler. Left-handers count from the left side of the lane instead.
The Lane Markings: Boards, Dots and Arrows
A ten-pin lane is made up of 39 boards (or, on synthetic lanes, printed board lines), each a little over an inch wide. Bowlers number them from the right edge for right-handers and from the left edge for left-handers.
There are seven arrows across the lane, five boards apart:
| Arrow (from the right) | Board | Common name |
|---|---|---|
| 1st | 5 | First arrow |
| 2nd | 10 | Second arrow |
| 3rd | 15 | Third arrow |
| 4th | 20 | Center arrow |
| 5th | 25 | Fifth arrow (or third from the left) |
| 6th | 30 | Sixth arrow |
| 7th | 35 | Seventh arrow |
The arrows form a shallow V shape, with the center arrow farthest down the lane.
Other markings you’ll see:
- Approach dots. Rows of dots on the approach (the area where you walk) are used to set where you stand. There’s usually a row near the foul line and more rows farther back. The large center dot marks board 20, and you can count boards out from it.
- Lane dots. A row of dots on the lane itself, a few feet past the foul line (often around 7 feet), in front of the arrows.
- Range finders. Some lanes have longer marks farther down, past the arrows, that help bowlers see where the ball is heading in the midlane.
What Are the Arrows Called?
Most bowlers simply call them arrows or targets, and refer to each one by number (“the second arrow”) or by board (“the 10 board”). Some coaches call the area around them the “arrow zone” or the “targeting area.”
Why Aim at the Arrows Instead of the Pins?
- Closer means more accurate. A small error in your release shows up as a much larger miss 60 feet away. Aiming at a mark 15 feet away makes errors easier to control and to see.
- You can see your mistakes. Watch the ball cross the arrows. If it missed your arrow, the problem was your release or swing. If it hit your arrow but missed the pocket, the problem is your line or the lane, not your aim.
- It works for hooks. A hook ball doesn’t head straight at the pins, so aiming at the pins doesn’t help. Aiming at an arrow gives the ball a starting line, and the lane does the rest.
Aiming at a mark on the lane is often called spot bowling. Aiming directly at the pins is pin bowling. Picturing the full path from release to pocket is line bowling. Most coaches recommend spot bowling, often combined with a sense of the line you want.
Arrows or Dots?
Both work. The choice is about what you can see and hit most consistently:
- Arrows are larger and easier to spot, and they’re where most bowlers start.
- Lane dots are closer, so some bowlers find them easier to hit. They suit bowlers who are very consistent and want the nearest possible target.
- Some bowlers use both, looking at a dot and an arrow on the same line so they have two points that define the path.
Pick one and stay with it, at least for a full session. Switching targets from shot to shot makes it hard to work out what’s going wrong.
Which Arrow to Aim For
There’s no single right arrow, but these are common starting points for right-handers on a typical house lane:
- Straight ball or small hook: start with the second arrow (board 10). Many beginners stand with the inside of the slide foot around the center dot on the approach (board 20) and adjust from there.
- Moderate hook: many bowlers start around the second arrow or between the second and third arrows (boards 10 to 15), standing farther left so the ball has room to hook back.
- Big hook: high-rev bowlers often play deeper, aiming around the third arrow or farther in and standing well left.
Treat these as a first shot, not an answer. After a few balls, the lane will tell you where to move.
How to Target the Arrows, Step by Step
- Pick your target arrow and your starting board on the approach.
- Line up. Stand so the inside edge of your slide foot is on your chosen board. Keep your shoulders roughly square to your target line.
- Fix your eyes on the target in your stance and keep them there through the release. Don’t look up at the pins until after the ball has passed the arrows.
- Walk toward your target. Your steps should follow the line you want, without veering. If you keep ending up on a different board, see why you drift on your bowling approach.
- Release and follow through toward the target, not toward the pins.
- Watch the ball cross the arrows and note which board it rolled over.
Adjusting When You Miss
If the ball rolls over your arrow but misses the pocket, move your feet, not your target:
- Ball hits high (goes left of the headpin for a right-hander): move your feet left a couple of boards.
- Ball hits light (goes right of the headpin): move your feet right a couple of boards.
A popular refinement is to move the feet two boards and the target one board in the same direction. See our guide to lane play adjustments and the 2-and-1 rule.
If the ball keeps missing the arrow itself, don’t move yet. Work on your release, swing and timing first. Our article on bowling timing is a good place to start.
Targeting for Spares
The arrows are just as useful for spares:
- Right-side spares (like the 10 pin): stand farther left and roll across the lane, often through the second or third arrow from the right.
- Left-side spares (like the 7 pin): stand farther right and roll across toward the left.
- Many bowlers follow a structured spare system that moves the starting position by a set number of boards for each pin while keeping the same target. A straight release makes this much more reliable. See the suitcase grip for bowling straight.
Arrow Practice Drills
- One-arrow sessions. Pick an arrow and spend a game trying to roll over it on every shot, without worrying about the pins. Count how many times you hit it.
- Board target. Ask a friend to watch and call out the board your ball crossed at the arrows. Try to keep it within one or two boards of your target.
- Two-point line. Pick a dot and an arrow on the same line and roll through both.
- Spare targeting. Practice the 10 pin and 7 pin using the same arrow-based system each time.
FAQ
What arrows should I aim for when bowling?
Many right-handed beginners start at the second arrow from the right (board 10). Hook bowlers often play a little deeper. Adjust your feet based on where the ball hits the pins.
Should you aim at the dots or the arrows?
Either can work. Arrows are easier to see and suit most bowlers. Dots are closer and suit some very consistent bowlers. What matters is choosing one and sticking with it.
Which arrows should I use for target practice?
Any arrow works for practice. The second arrow is a good default because it’s a common strike target and a common spare target.
How far are the arrows from the foul line?
They’re located roughly 15 feet past the foul line, with the center arrow slightly farther than the outside ones.