To bowl faster, start farther back on the approach, hold the ball higher in your stance, and let your footwork set a quicker tempo. Your arm should stay loose rather than forcing the ball. To bowl slower, do the opposite: move up, hold the ball lower and walk at a calmer pace. Ball speed is one of the most effective adjustments in bowling, because it changes how much and how early your ball hooks.
Why Ball Speed Matters
Speed and hook are closely linked:
- Faster: the ball spends less time on the lane, skids farther and hooks less, or later.
- Slower: the ball has more time to react, so it hooks more and earlier.
That’s why speed control is useful during a game. If your ball is hooking too early, a bit more speed can help. If it’s sliding past the pocket, slowing down slightly can help. Speed also needs to suit your rev rate. Our explainer on torque and rev rate covers speed-and-rev matching, and our article on length, backend and pin carry explains how speed affects carry.
How Fast Should You Bowl?
There’s no single right speed. One commonly cited classification, from a Storm glossary measuring speed at release, calls under about 17 mph slower, 17 to 19 mph medium, and over 19 mph faster. Speeds shown on scoring displays are often lower than release speed, because the ball slows down as it travels and many systems measure it farther down the lane.
As a practical guide:
- Recreational bowlers with a straight ball often benefit from a moderate, controllable speed rather than throwing hard.
- Hook bowlers generally need enough speed that the ball doesn’t hook too early, but not so much that it skids past the pocket.
- What matters most is consistency. A speed you can repeat within a mile per hour or so is worth more than a particular number.
Measuring Your Speed
Scoring displays
Many centers show speed after each shot. These numbers are useful for comparing your own shots on the same lanes, but different centers measure at different points with different sensors, so a reading at one center may not match another.
The stopwatch method
Have a friend time the ball from the moment it leaves your hand to the moment it hits the pins, then divide 40.91 by the time in seconds. For example, 40.91 ÷ 2.5 seconds ≈ 16.4 mph. The 40.91 comes from the 60-foot distance to the headpin: 60 feet per second is about 40.91 mph. Hand timing isn’t precise, but it’s good enough to see changes.
Ball tracking
Systems like Specto measure speed at several points down the lane. See USBC coaching and the Specto system.
How to Bowl Faster
- Start farther back. Move back roughly 6 to 12 inches and take the same number of steps. Your steps naturally get a bit longer and quicker to reach the foul line, which adds speed. This is often the simplest change.
- Hold the ball higher. Raising the ball in your stance (from waist toward chest height) creates a longer pendulum, and the ball swings faster on the way down.
- Make a bigger pushaway. Pushing the ball a little farther out and up lengthens the swing in the same way.
- Pick up your footwork tempo. Walk with a bit more pace, especially on the last two steps. Keep your balance.
- Consider a five-step approach. An extra step gives more momentum. See how to do a four-step approach and when to use five.
- Check your fit. If you’re squeezing a ball that doesn’t fit, your swing tightens and slows. A relaxed grip lets the ball swing freely.
- Stay loose. A relaxed arm swings faster than a tense one.
How to Bowl Slower
- Start closer to the foul line. Moving up shortens your steps and slows your tempo.
- Hold the ball lower in your stance, around waist height or slightly below, for a shorter swing.
- Make a smaller pushaway.
- Slow your first steps. Many bowlers find a deliberate first step sets a calmer pace for the whole approach.
- Keep the timing intact. Slowing down shouldn’t mean stopping or holding the ball back at the top of the swing.
Speed for Spares
Some bowlers roll spares slightly faster than strike shots to reduce hook and keep the ball on line, especially at corner pins. Combined with a plastic spare ball and a straight release, this makes spare shooting more predictable. See the suitcase grip for bowling straight.
Don’t overdo it. A ball thrown much harder than normal is often less accurate.
Mistakes to Avoid
- Muscling the arm. Forcing the ball forward with the shoulder or bicep usually costs accuracy and timing, and it adds strain. Let the swing and your legs create speed.
- Changing several things at once. Adjust one element (starting position, ball height or footwork) and see what happens.
- Rushing the approach. More speed shouldn’t cost you balance at the foul line. If you’re falling off your finish, slow down.
- Ignoring timing. If your feet speed up but your swing doesn’t, your timing will suffer. See bowling timing explained.
Drills
- Three-speed drill. Throw shots at a slow, normal and fast pace using only starting position and ball height, and note the speed readings.
- Same-speed challenge. Try to keep a full game within a narrow speed range on the scoring display.
- Footwork-only. Walk the approach without the ball at different tempos to feel the difference.
FAQ
Does a heavier ball make you bowl faster?
Not usually. A heavier ball often slows bowlers down because it’s harder to swing. Some bowlers find a slightly lighter ball lets them add speed without strain.
Why does my ball speed vary so much?
Common causes are inconsistent footwork, a pushaway that changes from shot to shot, and gripping too hard. A consistent stance height and starting position help.
Is it better to bowl fast or slow?
Neither. The right speed is one that suits your rev rate and the lane, and that you can repeat.