Drilling and Layouts

Bowling Ball Drilling Layouts: Pin Placement and Hole Positions Explained

How bowling ball drilling layouts work: the pin, CG and mass bias, your PAP, pin-to-PAP distance, drill angles, hole placement and balance holes, explained plainly.

On this page
  1. What a Drilling Layout Actually Is
  2. The Markings You Need to Know First
  3. The Positive Axis Point: The Starting Point for Every Layout
  4. How Pin Placement Changes Ball Reaction
  5. Mass Bias Placement and Drill Angle
  6. Hole Placement: Fit Versus Layout
  7. Layout Systems Pro Shops Use
  8. Balance Holes and Extra Holes
  9. Symmetrical vs Asymmetrical Cores
  10. Choosing a Layout: Style and Lane Condition
  11. How Much Does Layout Really Matter?
  12. Working With Your Pro Shop

What a Drilling Layout Actually Is

When a pro shop drills a reactive bowling ball, it does two separate jobs at once.

The first is fit: the size of the thumb and finger holes, the span between them, and the angles (pitches) they’re drilled at. Fit is about your hand.

The second is layout: where those holes sit relative to the ball’s core. The core (also called the weight block) is the dense shape inside the ball. Where it sits relative to your grip and your release decides how much the ball flares, when it starts to hook, and how sharply it changes direction at the back of the lane.

Two bowlers can buy the same ball and get very different motion from it because their layouts are different. A layout won’t turn a mild ball into a heavy-oil weapon, but it can move the same ball’s reaction earlier or later, smoother or sharper, to suit your style and the lanes you bowl on.

The Markings You Need to Know First

Most reactive balls come with markings that show where the core sits. If you’re not sure what the dots on your ball mean, our guide to what the colored dots on bowling balls mean walks through each one.

The Pin

The pin marks where the top of the core’s axis meets the ball’s surface. On many balls it’s a small colored dot or ring. Pin placement is the core of most layout descriptions: “pin above the fingers,” “pin 4 inches from the PAP,” and so on.

The Center of Gravity (CG)

The CG marks the heaviest side of the undrilled ball. It’s often a small engraved dot, and on some older balls it sits near the logo. Some newer balls don’t mark it at all. The CG matters mostly for static balance, meaning whether the drilled ball stays within the weight limits for sanctioned play.

The Mass Bias (PSA) on Asymmetrical Balls

Asymmetrical balls have a core that isn’t the same in every direction. They usually carry a third marking for the mass bias, also called the PSA (preferred spin axis). It shows the direction in which the core is most lopsided. Placing the mass bias is how drillers fine-tune how sharply an asymmetrical ball changes direction.

In bowling, “bias” almost always means this mass bias. It’s the direction the core “wants” to spin around.

The Positive Axis Point: The Starting Point for Every Layout

Before a driller can place the pin or mass bias, they need to know your positive axis point (PAP). It’s the point on the ball’s surface that your release makes the ball spin around, at one end of its axis of rotation. For right-handers it’s on the right side of the grip; for left-handers it’s on the left.

Every layout is measured from your PAP. A pin placed 4 inches from one bowler’s PAP might sit 5 inches from another bowler’s PAP, so it’s the same pin location on the ball but a different reaction. That’s why good pro shops measure your PAP before suggesting a layout. If you want to find it yourself, see our step-by-step guide on how to find your positive axis point and measure pin-to-PAP distance.

How Pin Placement Changes Ball Reaction

Pin-to-PAP Distance

The distance from the pin to your PAP is one of the biggest layout levers. As a general guide:

Pin-to-PAP distance Typical effect
Very close (roughly 1–2 inches) Less flare, smoother and more controllable. Often used for control or for very dry or very high-friction conditions
Around 3 3/8 inches Commonly cited as the position with the most flare potential. On a standard-size ball it’s about an eighth of the ball’s circumference from the PAP
Around 4–5 inches A popular all-around range with strong but not maximum flare
Farther (5 1/2 inches and beyond) Flare drops off again. The ball usually skids longer and saves energy for the backend

These are rules of thumb, not guarantees. The ball’s core, its coverstock, and your speed and rev rate all change how a given distance plays.

Pin Above or Below the Fingers

You’ll often hear layouts described as “pin up” or “pin down”.

  • Pin up (pin above the finger holes) tends to produce more length and a stronger backend reaction. It’s often used when you want the ball to save energy, such as on lighter oil or when the lanes break down.
  • Pin down (pin below the finger holes) tends to produce an earlier, smoother, more arcing motion. It’s often used when you want the ball to read the lane sooner.

These descriptions are shorthand and don’t tell the whole story on their own. Where the pin sits relative to your PAP matters more than where it sits relative to your fingers.

Mass Bias Placement and Drill Angle

On asymmetrical balls, the second big lever is where the mass bias sits. Most drillers describe this with a drill angle: the angle at the pin between the line to your PAP and the line to the mass bias.

The common pattern:

  • Lower drill angles (roughly under 45 degrees) tend to make the ball start hooking earlier with a smoother, more rounded motion.
  • Higher drill angles (roughly over 60 degrees) tend to push the hook later and make it more angular.

The drill angle is part of the Dual Angle layout system, which also uses pin-to-PAP distance and a third measurement called the VAL angle. Our explanation of the Dual Angle layout system covers all three numbers in detail.

Hole Placement: Fit Versus Layout

The phrase “hole placement” covers two different things:

  1. Where the holes are drilled relative to each other. That’s the span, bridge and pitch, which are all fit. It should be based on your hand, not on the layout. If your hand fit is wrong, no layout will help. See how your hand should fit a bowling ball and our guide to forward, reverse and lateral pitch.
  2. Where the whole grip sits on the ball relative to the core. That’s the layout. The driller rotates your grip around the ball until the pin and mass bias land where the layout calls for.

Your grip style also matters. Fingertip and conventional grips place the holes differently and release the ball differently. If you’re deciding between them, read fingertip vs conventional grip first.

Layout Systems Pro Shops Use

There’s no single universal language for layouts. You’ll run into a few common systems:

  • Pin and CG descriptions (“pin up, CG kicked out”): the older, informal way of describing layouts. It’s still common for symmetrical balls and casual conversation.
  • The Dual Angle system: written as three numbers, such as 50 x 4 1/2 x 40 (drill angle, pin-to-PAP distance, VAL angle).
  • Distance-based systems such as Storm’s VLS, which describe layouts by measuring distances from the PAP and VAL instead of angles.

They describe the same physical thing in different ways. When you get a layout recommendation, ask which system it’s written in.

Balance Holes and Extra Holes

Sometimes a driller adds an extra hole that you don’t grip, called a balance hole or weight hole. Historically it was used to bring a drilled ball back within static weight limits or to tweak reaction. Under USBC rules, a ball can have only one balance hole, and size limits apply. USBC also treats an unused thumb hole as a balance hole for bowlers who don’t put their thumb in.

Many modern layouts are designed to avoid needing a balance hole at all. If your ball already has extra holes you want to change, see our guide to plugging and redrilling a bowling ball. For the rules on which holes you actually have to use, read do you have to use the holes when bowling.

Symmetrical vs Asymmetrical Cores

  • Symmetrical cores have no meaningful mass bias, so layouts mostly come down to pin-to-PAP distance and pin height. They’re generally more forgiving and predictable.
  • Asymmetrical cores add the mass bias as a second lever. That gives drillers more ways to shape the motion, but it also gives them more ways to get it wrong.

Choosing a Layout: Style and Lane Condition

A layout is usually chosen around two things:

  • Your release. Bowlers whose speed outweighs their revs (“speed-dominant”) often benefit from layouts that help the ball start hooking. Rev-dominant bowlers often want layouts that delay or tame the motion. Our stroker layout guide covers lower-rev players. Two-handed and no-thumb bowlers have their own considerations, covered in thumbless bowling layouts.
  • The lanes. Heavier oil usually calls for layouts that help the ball read the lane earlier. Drier lanes usually call for layouts that add length and control. See our layouts for heavy oil and dry lanes.

Many bowlers with more than one ball drill each with a different layout so the arsenal covers a range of conditions.

How Much Does Layout Really Matter?

Layout matters, but it isn’t the biggest factor. Many coaches and pro shop operators consider the coverstock (its type and surface finish) the largest influence on how a ball reacts, with the core and layout fine-tuning the shape of that reaction. Your release, speed and accuracy matter more than either.

In practice:

  • A good layout makes a well-chosen ball match you better.
  • A layout can’t rescue a ball that’s badly wrong for the conditions.
  • Small changes, like half an inch of pin distance or 10 degrees of drill angle, can be hard to feel unless you’re a very consistent bowler.

Working With Your Pro Shop

A good driller will usually:

  1. Watch you bowl or ask about your speed, rev rate and typical lane conditions.
  2. Measure or estimate your PAP.
  3. Measure your hand for span, pitch and hole sizes.
  4. Ask what the ball needs to do in your arsenal.
  5. Suggest a layout and explain the reasoning.

Ask questions, keep a record of the layout on each ball, and tell the driller how the ball actually reacts. Drilling is permanent short of a plug and redrill, so it’s worth taking a few minutes to get it right. If you’re budgeting, see how much it costs to have a bowling ball drilled.

Keep exploring

Guides from other topics

All topics →