Lanes and Machines

What are bowling alleys made of?

Bowling lanes are made of maple and pine boards or synthetic laminate panels. Here's what each part of a bowling alley is made of and how wood and synthetic compare.

On this page
  1. Wood lanes: maple and pine
  2. Synthetic lanes
  3. Wood vs synthetic: how they compare
  4. What’s under the lane
  5. The other parts: approach, gutters, pin deck, kickbacks and pit
  6. What about the pins and balls?
  7. Does lane material affect how the ball reacts?

Bowling lanes are made of either wood or synthetic material. Traditional wood lanes use hard maple where the ball lands and where the pins stand, and softer pine for the long middle section. Most modern bowling centers have switched to synthetic lanes: tough laminate panels printed to look like wood, often laid directly over the old wooden lanes.

Here’s a closer look at each part.

Wood lanes: maple and pine

A traditional wood lane is built from about 39 long, narrow boards placed side by side. The boards are set on edge, not flat, which makes the surface stronger. They’re glued and fastened together, then sanded flat and finished with a protective coating.

Two woods are used, each where it suits best:

  • Maple is very hard and resists denting. It’s used on the approach, the first section of the lane past the foul line (the heads, where the ball lands), and the pin deck, where pins are hit and bounce around.
  • Pine is softer and lighter. It’s used for the long middle part of the lane, where the ball is rolling rather than landing.

You can often see the joint on an old wood lane: the color and grain change a few feet past the arrows, where maple gives way to pine.

Wood lanes need regular care. Over time the finish wears, the boards dent and the surface can develop small dips. They’re periodically resurfaced: sanded down and refinished.

Synthetic lanes

Synthetic lanes are made from high-pressure laminate, a layered material similar in principle to very heavy-duty countertop laminate. The panels are printed with a wood-grain image, including board lines, dots and arrows, and topped with a hard, wear-resistant surface layer.

Synthetic surfaces are installed in two main ways:

  • Overlays: thin synthetic panels laid over the existing wood lane, often after the wood has been sanded flat. This is a common way to upgrade an older center.
  • Full synthetic lanes: complete synthetic panels installed on a new or rebuilt base.

Some centers have only replaced part of the lane, such as the heads or the pin deck, with synthetic material, which is why you’ll occasionally see a lane that looks half wood and half synthetic.

Wood vs synthetic: how they compare

Wood Synthetic
Durability Dents and wears; needs refinishing Very hard-wearing
Maintenance Periodic sanding and recoating Mostly cleaning and oiling
Consistency Changes with humidity and wear Generally more stable
Look Real wood grain Printed wood grain or custom graphics
Lifespan Long if maintained Long, but panels eventually need replacing

Most centers choose synthetic for lower upkeep and consistency, although some bowlers prefer the feel of well-kept wood.

What’s under the lane

The playing surface sits on a supporting structure, not straight on the floor. In a typical installation, a framework of sleepers or levelers rests on the concrete slab and is carefully shimmed so the lane is flat. The lane bed or panels sit on top. Getting this base right matters: certified lanes have to be level to within very small tolerances, which inspectors check during lane certification.

The other parts: approach, gutters, pin deck, kickbacks and pit

  • Approach: maple or synthetic, matching the lane, and kept free of oil
  • Gutters (channels): usually formed from synthetic or composite material in modern installations; older lanes used wood or metal
  • Capping: the raised strips between lanes, usually synthetic or wood
  • Pin deck: maple on wood lanes, or a dense synthetic insert on synthetic lanes
  • Kickbacks: the tall side walls at the pin deck, faced with tough panels that pins bounce off
  • Pit: a lowered area with a cushion or curtain at the back to stop the ball and pins

For how these parts work together, see our overview of how a bowling alley works and our article on gutters and bumpers.

What about the pins and balls?

Pins are made of glued-up hard maple with a plastic coating, usually nylon or Surlyn. See bowling pin specs and setup and who makes bowling pins for more.

Bowling balls have an inner core (weight block) surrounded by an outer coverstock made of plastic (polyester), urethane or reactive resin. The core shape and the coverstock both affect how much the ball hooks.

Does lane material affect how the ball reacts?

Yes, somewhat. The lane surface, its age and wear, and how it takes oil all affect ball motion. Wood and synthetic surfaces can react differently to the same oil pattern, and a worn wood lane plays differently from a freshly refinished one. In practice, though, the oil pattern has a much bigger effect on how the lane plays than the material underneath. See what a house shot is and how lanes change during play.

The complete guide to lanes and machines

How a Bowling Alley Works: Lanes, Pins, Pinsetters and More
Read the guide

Keep exploring

Guides from other topics

All topics →