Spares

How to Pick Up the 10 Pin: Tips for Right-Handed Bowlers

Right-handed bowlers miss the 10 pin more than any other spare. Learn the cross-lane setup, target, ball choice and release that make it routine.

On this page
  1. Why the 10 pin is so hard for right-handers
  2. Step 1: Use a ball that won’t hook into the channel
  3. Step 2: Move to the left side of the approach
  4. Step 3: Pick a target
  5. Step 4: Face your target and walk toward it
  6. Step 5: Flatten your release
  7. Troubleshooting your 10-pin misses
  8. How to practice the 10 pin
  9. Left-handers: the 7 pin is your 10 pin

The 10 pin is the spare right-handed bowlers love to hate. It often shows up after a shot that looked good, and it’s sitting just a few boards from the right channel. The reliable way to pick it up is a cross-lane shot from the left side of the approach, with a ball and release that don’t hook. Here’s how to set that up.

Why the 10 pin is so hard for right-handers

A right-hander’s natural hook moves from right to left, which is away from the 10 pin. To reach the 10 with a hooking ball, you have to fight that motion and keep the ball close to the edge of the lane, where one small mistake drops it in the channel.

The 10 pin also often appears after a solid-looking strike shot — when the 6 pin flies around it or lies down in front of it. Bowlers sometimes call this a “ringing 10” or “weak 10.” That frustration can make the next shot tense, which is one more reason to have a fixed routine.

The fix is to remove hook from the equation and give the ball as much lane as possible.

Step 1: Use a ball that won’t hook into the channel

If you have a plastic (polyester) ball, use it. Plastic is a low-friction material that tends to travel straight instead of curving back left. If you only have one ball, you can still pick up the 10 with a straighter release (Step 5), but a plastic ball makes it much easier, especially if you throw a big hook.

Our guide to spare bowling balls explains why polyester goes straight and what weight to choose.

Step 2: Move to the left side of the approach

Move well to the left on the approach. Many right-handers slide somewhere around the low-to-mid 30s boards, near the last approach dot on the left side. The exact spot depends on your drift (how far you walk sideways during your approach) and where the ball leaves your hand, which is usually several boards to the right of your slide foot.

Standing left creates angle. Instead of rolling parallel to the channel, the ball crosses the lane diagonally toward the 10. That angle means a slightly-off shot still has a good chance of clipping the pin rather than dropping off the edge. A ball and pin together give you roughly a foot of contact window, so the pin is a bigger target than it looks.

Step 3: Pick a target

Two targets are common:

  • The center arrow (4th arrow, board 20). The middle of the lane usually has the most oil, which helps the ball skid instead of hooking. Some coaches favor this target because it creates a sharper angle across the lane.
  • The third arrow (board 15). Also used for cross-lane spares, with a slightly less extreme angle.

Some bowlers find it easier to aim at the lane dots closer to the foul line, then let their swing carry the ball through the matching arrow.

Pick one target, combine it with your stance from Step 2 and test it in practice. If the ball consistently misses on one side, adjust your feet by a board or two and keep the target the same.

Step 4: Face your target and walk toward it

This is where many 10-pin misses come from. When you move far left, your body should turn to face the target line, not the head pin.

  • Angle your shoulders and hips toward your target.
  • Walk toward the target on your approach. On a cross-lane shot, your steps should drift slightly right along the line, not straight down the boards.
  • Keep your eyes on the target until the ball passes it.

A common mistake is to move the feet left but walk and swing toward the middle of the pin deck, which pulls the ball left of the 10.

Step 5: Flatten your release

Whether you’re using plastic or your strike ball, change your release for this shot:

  • Keep your hand behind the ball, fingers underneath, with the thumb pointing toward the pins.
  • Avoid turning your hand around the side of the ball.
  • Let the ball roll closer to end over end. Some bowlers bend the wrist back slightly to reduce hook further.
  • Finish with your palm up and your arm reaching toward your target.
  • A little extra speed can help limit any remaining hook. Stay smooth — accuracy matters more than pace.

Troubleshooting your 10-pin misses

What happens Likely cause Try this
Ball goes in the right channel before the pin Too much angle, or ball fading right on dry boards Move feet a board or two right, or target slightly left; check you’re not pushing the ball
Ball misses left of the pin Ball hooking, or pulling the shot Use plastic, flatten your hand, check that you’re walking toward the target
Ball misses left even with plastic Walking straight or swinging across your body Angle your shoulders and walk along the target line
Results are inconsistent Changing setup each time Fix one stance and one target, and only adjust by small amounts

How to practice the 10 pin

You don’t have to wait for a 10 pin to practice one. Set up on your 10-pin line and throw at a full rack. If your line is right, the ball will clip the 10 pin as it passes. Count each throw where the 10 falls as a success.

Do this for a full practice game and track your makes. Our spare drills include this and other routines, such as alternating 7-pin and 10-pin lines.

The 10-pin line is also a key part of any full spare system. For the 3, 6 and 6-10 type leaves on the right side, see our guide to spare alignment and the 3-6-9 system.

Left-handers: the 7 pin is your 10 pin

For left-handed bowlers, everything above applies in mirror image to the 7 pin, which sits by the left channel. Move to the right side of the approach, target the center or third arrow from the left, and shoot cross-lane. Our guide on how to pick up the 7 pin covers that pin from both sides.

The complete guide to spares

How to Pick Up Spares: Alignment and the 3-6-9 System
Read the guide

Keep exploring

Guides from other topics

All topics →