Ball Construction

Static Weight in Bowling Balls: Top Weight, Side Weight and Pin Weight

What top weight, side weight, finger and thumb weight and pin weight mean on a bowling ball, what the rules allow, and how much static weight affects reaction.

On this page
  1. Static weight vs dynamic weight
  2. Top weight (and bottom weight)
  3. Side weight
  4. Finger and thumb weight
  5. Pin weight, pin length and what you pick when ordering
  6. What the rules allow
  7. Does static weight change ball reaction?
  8. Practical advice when buying and drilling

Static weight vs dynamic weight

Bowling ball weight comes in two senses:

  • Total weight is what the ball weighs on a scale, such as 14 or 15 pounds. The legal maximum is 16 pounds. To choose yours, see what weight bowling ball should I have?
  • Static weight is the small imbalance between one side of the ball and another when it sits still on a scale, measured in ounces. Top weight and side weight are both forms of static weight.

Dynamic weight describes how mass is distributed when the ball is spinning. It is captured by the core’s RG and differential numbers, which are covered in RG and differential explained.

“What is the weight inside a bowling ball called?” The dense inner piece is the weight block or core. Our bowling ball anatomy guide describes how it sits inside the filler and coverstock.

Top weight (and bottom weight)

Top weight is how much heavier the top half of the ball (the side where the holes go) is than the bottom half. Bottom weight is the reverse.

Undrilled balls are built with some extra weight on top on purpose, because drilling finger and thumb holes removes material from that area. In a test published by Creating The Difference (CTD), the normal manufacturer range of top weight on a new ball was given as about 2 to 4 ounces, and drilling was said to remove about 1 to 2 ounces. The goal is for the finished, drilled ball to be close to balanced and within the rules.

The more weight removed by drilling (bigger holes, deeper holes, extra holes), the more top weight a driller has to work with. A pro shop will weigh the ball on a static scale after drilling to confirm it is legal.

Side weight

Side weight is the imbalance between the left and right sides of the ball relative to the grip. Positive side weight is on the side toward your palm (thumb side for many bowlers), and negative side weight is on the other side. Exact conventions vary.

Side weight usually comes from where the holes are drilled relative to the ball’s center of gravity (CG), rather than something you choose when you buy the ball.

Finger and thumb weight

Finger weight and thumb weight describe the imbalance between the finger-hole side and the thumb-hole side. Like side weight, they mostly result from where the grip is placed relative to the CG.

Pin weight, pin length and what you pick when ordering

When you order a performance ball, you may see options for top weight and pin length (sometimes called pin distance or pin weight), such as “2–3 oz top weight, 3–4 inch pin.” Here is what those mean:

  • The pin is a marker, usually a small colored dot, showing the top of the core’s main axis.
  • Pin length is the distance from the pin to the CG on the undrilled ball.
  • Top weight is the static weight described above.

Pin length gives the driller more or fewer layout options. For example, it affects whether the pin can end up above the fingers while the CG stays near the middle of the grip. For more, see pin up vs pin down and what a 4-5 inch pin means.

If you are not sure what to choose, ask the pro shop that will drill the ball. They can pick combinations that suit your layout.

What the rules allow

The United States Bowling Congress (USBC) sets static weight limits for sanctioned play. The best-known limit is top weight: according to CTD, a drilled ball can have no more than 3 ounces of top (or bottom) weight. Side and finger/thumb weight have historically been capped at around 1 ounce each for full-weight balls, with different allowances for lighter balls.

USBC has changed equipment rules over the years. Notably, it eliminated balance holes (extra holes drilled only to adjust static weight) starting in 2020, so static weight now has to be managed through the layout itself. Because specifications are revised from time to time, check current USBC equipment specifications or ask a certified pro shop before relying on any specific number.

Does static weight change ball reaction?

Within legal limits, the effect appears to be small for modern balls with large dynamic cores.

CTD tested balls that were identical except for top weight, including some well over the legal limit. The ball with the most top weight (6.6 ounces, illegal) hooked slightly earlier and entered the pocket at a slightly higher angle than the ball with the least. However, the entry angle difference across the whole range was under 2 degrees. CTD’s conclusion was that within the 3-ounce limit, top weight’s measurable effect on performance is minimal at best.

Static weight mattered more in the days of pancake weight blocks, when the core itself did little to shape the ball’s motion. Some bowlers still talk about side weight adding hook or length, but for most modern equipment the core design, cover and layout matter far more.

Practical advice when buying and drilling

  • Don’t stress about top weight on a modern performance ball. A standard option is fine for most bowlers.
  • Let the pro shop choose pin length and top weight if you are unsure, especially if you plan a specific layout.
  • Ask for a static weight check after drilling, particularly if you bowl in USBC-certified competition.
  • Plugs and redrills change static weight, so the ball should be rechecked after any redrill.
  • Lighter balls may use different core designs, and the static weight considerations can differ. See does a heavier bowling ball hook more? for how weight changes core design.

The complete guide to ball construction

Bowling Ball Anatomy: Cores, Coverstocks and How They Shape Ball Reaction
Read the guide

Keep exploring

Guides from other topics

All topics →