Drilling and Layouts

What do the colored dots on bowling balls mean?

The colored dots on a bowling ball show where the core sits: the pin, the CG and the mass bias. Here's what each marking means and why drillers use them.

On this page
  1. The Short Answer
  2. The Pin
  3. Pin-In vs Pin-Out
  4. The CG Marking
  5. The Mass Bias Marker
  6. Quick Reference Table
  7. Why the Markings Matter When Drilling
  8. What If Your Ball Doesn’t Have These Markings?

The Short Answer

The colored dots and small marks on a reactive bowling ball show where the core (weight block) sits inside the ball. There are usually up to three:

  • The pin, often a colored dot or ring, which marks the top of the core
  • The CG (center of gravity), often a small dot or engraved mark, which marks the heavy side of the ball
  • The mass bias (also called the PSA), on asymmetrical balls only, which marks the direction the core is most lopsided

They aren’t decorations or weight labels. They’re layout markers for the pro shop that drills the ball.

The Pin

The pin marks the spot where the top of the core’s axis comes out at the ball’s surface. On many reactive balls it’s a small colored dot, sometimes surrounded by a ring. Its color often contrasts with the cover, though colors vary by brand and model.

The pin is the main reference point drillers use to describe a layout: “pin 4 inches from your PAP” or “pin above the fingers.” Where the pin ends up relative to your grip and your release has a big influence on how much the ball flares and when it hooks. See our guide to bowling ball drilling layouts for how pin placement changes the reaction.

Pin-In vs Pin-Out

You’ll sometimes see balls described as “pin-in” or “pin-out”:

  • Pin-in: the pin sits very close to the CG.
  • Pin-out: the pin sits farther from the CG.

The distance between the pin and CG affects which layouts the driller can choose while keeping the ball within static balance limits. It’s a factor in layout planning, not a sign of quality. Neither type is better.

The CG Marking

The CG marks the heaviest side of the undrilled ball. It’s often a small dot or engraved mark, and on some older balls it sits near the logo. Drillers use it mainly to keep the drilled ball within USBC static balance limits for certified competition.

Not every ball marks the CG. Some newer balls leave it unmarked, and drillers can locate it on a balance scale if they need it.

The Mass Bias Marker

Asymmetrical balls have cores that aren’t the same in every direction. They usually carry an extra marker for the mass bias, also called the PSA (preferred spin axis). It shows the direction the core “wants” to spin toward.

When bowlers talk about “bias” in a layout, this is what they mean. Placing the mass bias in different spots relative to your PAP helps shape how sharply the ball changes direction. Symmetrical balls have no meaningful mass bias, so they usually don’t have this marker.

Quick Reference Table

Marking Typical appearance What it shows Found on
Pin Colored dot, sometimes with a ring Top of the core’s axis Most reactive balls
CG Small dot or engraved mark, sometimes near the logo Heavy side of the undrilled ball Many balls; not always marked
Mass bias / PSA Small dot or mark, often separate from the pin and logo Direction of the asymmetrical core’s bias Asymmetrical balls

Markings vary by manufacturer. If you can’t tell which is which, the manufacturer’s spec sheet or any pro shop can identify them in seconds.

Why the Markings Matter When Drilling

When a pro shop lays out a ball, it starts with your positive axis point (PAP), the point your release makes the ball spin around. The driller then decides where the pin and mass bias should sit relative to your PAP. Finally, they rotate your grip (thumb and finger holes) around the ball to put those markings where the layout calls for them.

Without the markings, the driller couldn’t place the core deliberately. To understand the PAP, see how to find your positive axis point. For a common angle-based way of describing where the pin and mass bias go, see our explainer on the Dual Angle layout system.

What If Your Ball Doesn’t Have These Markings?

  • House balls at bowling centers usually have simple cores, and their markings are rarely used for layout.
  • Plastic or polyester spare balls often have small, simple cores where pin placement makes little practical difference.
  • Older or worn balls may have faded marks. A pro shop can usually still find the core with a spin or balance test.

If you’re buying your first reactive ball, it’s worth asking the pro shop to show you the markings before they drill. Knowing what’s on your ball makes it easier to talk with your driller about future layouts.

The complete guide to drilling and layouts

Bowling Ball Drilling Layouts: Pin Placement and Hole Positions Explained
Read the guide

Keep exploring

Guides from other topics

All topics →