Ball Construction

Pin Up vs Pin Down Bowling Balls (and What a 4-5 Inch Pin Means)

Pin up vs pin down layouts explained: where the pin sits, how each tends to roll, what a 4-5 inch pin length means when ordering, and how to choose.

On this page
  1. First: what the “pin” on a bowling ball is
  2. Pin up vs pin down: the basic difference
  3. How each tends to roll
  4. Pin length: what a 4-5 inch pin means
  5. Pin length vs pin-to-PAP distance
  6. Does pin length affect ball reaction?
  7. Choosing between pin up and pin down
  8. Questions to bring to your pro shop

First: what the “pin” on a bowling ball is

On a bowling ball, the pin is not a bowling pin. It is a small marker on the surface, often a colored dot, that shows where the top of the weight block’s main axis is. It is left over from the manufacturing process, where the core is held in position while the cover is poured.

Bowlers often look up “pins” questions and find answers about the ten pins at the end of the lane. That is a different subject entirely. Here we are only talking about the marker on the ball.

Most performance balls also have a CG (center of gravity) mark, and asymmetric balls have a third mark for the mass bias or PSA. Together, these tell the driller where the core sits. Our bowling ball anatomy guide explains how they fit into the bigger picture.

Pin up vs pin down: the basic difference

The terms describe where the pin ends up relative to your finger holes after the ball is drilled:

  • Pin up: the pin sits above the finger holes, toward the top of the ball as you hold it.
  • Pin down: the pin sits below the finger holes, between the fingers and the thumb or closer to the thumb.

Neither is a different ball; they are different ways of drilling the same ball. Because the pin marks the core’s orientation, moving it changes how the core is positioned relative to your grip and your axis of rotation.

How each tends to roll

These are general tendencies. Drillers and coaches stress that they are rules of thumb, not guarantees, because the full layout, your positive axis point (PAP), your speed and rev rate, and the ball’s surface all play a role.

Pin up layouts are generally associated with:

  • More length before the ball starts hooking.
  • A quicker, sharper change of direction downlane.
  • More recovery for bowlers playing deeper angles or facing drier backends.

Pin down layouts are generally associated with:

  • An earlier, smoother, more gradual motion.
  • A more predictable, controllable shape.
  • Fewer big jumps when the ball moves from oil to dry boards.

Some sources describe the difference in terms of the core: pin up layouts often produce wider flare and a stronger response, while pin down layouts usually produce tighter flare and a smoother arc. You can read how flare connects to the core numbers in RG and differential explained.

Pin length: what a 4-5 inch pin means

When you buy a performance ball, you may be asked to pick a pin length, often in ranges like “1–2 inch,” “2–3 inch,” “3–4 inch” or “4–5 inch.” Pin length is the distance between the pin and the CG on the undrilled ball.

  • A short pin (pin close to the CG, sometimes called “pin in”) limits how far apart the driller can place the pin and the grip center.
  • A longer pin, such as 4–5 inches, places the pin far enough from the CG that the driller can put the pin above the finger holes while keeping the CG near the middle of the grip. That makes pin-up layouts easier for many hand sizes.

So a “4–5 inch pin” is mostly about layout options. It does not mean the ball itself is stronger. Pin length and top weight are often chosen together on ball orders; we cover top weight in static weight: top, side and pin weight.

Pin length vs pin-to-PAP distance

These two terms are easy to confuse:

  • Pin length (pin-to-CG) is fixed by the manufacturer before drilling.
  • Pin-to-PAP distance is chosen by the driller. It is the distance between the pin and your positive axis point, so it depends on your release.

Pin-to-PAP distance has a large effect on flare. A pin very close to your PAP produces little flare. As the distance increases, flare generally increases to a peak somewhere around 3 to 4 inches for many symmetric balls, then decreases again. Drillers use this distance, plus the pin’s position relative to the fingers, to tune the reaction.

Does pin length affect ball reaction?

Indirectly. Pin length on its own does not change the core, but it limits which layouts are possible for your hand. If you want a pin-up layout and the pin is too short, the driller may not be able to place it where they want without moving the CG well outside the grip. That is why pro shops sometimes ask for a specific pin length when ordering.

For symmetric balls, pin length is mostly a drilling convenience. For asymmetric balls, the position of the mass bias marker adds another variable. Our symmetric vs asymmetric guide covers that.

Choosing between pin up and pin down

A rough guide, assuming everything else is equal:

You want… Often a fit
More length and a sharper backend Pin up
An earlier, smoother, more controllable roll Pin down
More recovery when playing deep inside angles Pin up
A ball that stays calm on heavy oil or for high-rev players Pin down

Many bowlers pair layouts with covers. For example, a pearl drilled pin up gives a strong backend, while a solid drilled pin down gives a smooth, controlled arc. The cover usually matters more than the layout, so if a ball is far too strong or weak, a different cover or surface is often the better fix. See solid, pearl and hybrid reactive covers.

Questions to bring to your pro shop

  • What does this layout do for my speed and rev rate?
  • Is this ball’s pin length right for the layout you want?
  • Will this layout fill a gap in my arsenal or duplicate a ball I already have?
  • How will the static weights end up after drilling?

A good driller will want to see you throw, or at least know your PAP, before recommending a layout.

The complete guide to ball construction

Bowling Ball Anatomy: Cores, Coverstocks and How They Shape Ball Reaction
Read the guide

Keep exploring

Guides from other topics

All topics →