Ball Construction

Why Bowling Balls Crack and How to Prevent It

Bowling balls usually crack from sudden temperature changes, stress around drilled holes, insert glue and aging. Learn the warning signs, prevention and repair options.

On this page
  1. The short answer
  2. Where cracks usually start
  3. The main causes
  4. How to prevent cracks
  5. Is a cracked ball still usable?
  6. Warranty and repair

The short answer

Bowling balls most often crack because of sudden temperature changes, stress around drilled holes, problems with finger inserts or glue, and aging of the cover material. Modern balls are made of several materials that expand and contract at different rates, so rapid heating or cooling puts stress on the shell. Cracks then tend to start at weak points such as the edges of holes.

Most cracking can be prevented with sensible storage, gradual warm-up after cold exposure, and good drilling and finishing at the pro shop.

Where cracks usually start

Cracks most often appear:

  • Around the thumb hole or finger holes, especially at sharp edges.
  • Across the bridge, the gap between the finger holes.
  • Around finger or thumb inserts, sometimes as a small web of fine cracks.
  • Around plugs from previous drilling.

Cracks away from the holes are less common, but they can occur, especially after temperature shock or a hard impact.

The main causes

Temperature changes

A bowling ball’s cover, filler and weight block are different materials (see our bowling ball anatomy guide). When temperature changes quickly, these layers expand or contract at different rates, which can create stress and cracks.

Common examples:

  • Leaving a ball in a car trunk in winter, then bowling with it immediately in a warm center.
  • Leaving a ball in a hot car in summer.
  • Storing a ball in an unheated garage or shed.

Drilling and hole finishing

  • Sharp hole edges concentrate stress. A pro shop normally bevels or rounds the edges to reduce this.
  • Thin bridges between the finger holes leave less material to hold the shell together.
  • Holes drilled very close to each other or to an old plug can create weak spots.

Inserts and adhesives

Finger inserts and thumb slugs are often held in with adhesive. Using too much or the wrong kind is commonly blamed for small cracks around inserts, because the glue and the cover may respond differently to temperature and stress. Pro shops usually follow the insert maker’s recommendations for fitting.

Impacts and wear

Dropping a ball on a hard floor, knocking balls together, or repeated hard contact in the ball return can chip or weaken the cover over time.

Material aging

Reactive and particle covers change slowly as they age and absorb oil. Some sources say this can make covers more prone to cracking over many years. The evidence is mostly anecdotal, but older reactive balls do seem more likely to crack than newer ones.

How to prevent cracks

  • Keep balls at moderate temperatures. Don’t leave them in a car or anywhere very hot or cold for long periods.
  • Let a cold or hot ball return to room temperature before you bowl with it. Keeping it in its bag while it adjusts is a common recommendation.
  • Store balls in a bag or box rather than loose on a hard floor.
  • Ask your pro shop to bevel and finish the holes and to leave an adequate bridge.
  • Have inserts fitted properly, using the recommended adhesive and amount.
  • Follow the manufacturer’s guidance on heat for any oil-extraction method, such as warm-water soaking or heated devices. Too much heat can harm a ball.
  • Handle balls carefully and avoid dropping them or knocking them together.
  • Inspect your balls regularly around the holes for fine lines.

Is a cracked ball still usable?

It depends on the crack:

  • Small cracks around an insert or hole edge can sometimes be repaired by plugging and redrilling, or by refitting the insert.
  • Larger cracks, cracks across the bridge or cracks that are growing usually make a ball unsafe or unreliable to use.

Because a cracked ball can fail during delivery, have a pro shop inspect any crack before you keep bowling with it. USBC also has rules about the condition of balls used in sanctioned play, so a visibly damaged ball may not be acceptable in competition.

Warranty and repair

Many manufacturers offer a warranty that covers cracking within a set period after purchase, subject to conditions such as proper drilling by a qualified pro shop and no misuse. Terms vary by brand, so:

  • Keep your receipt and note when and where the ball was drilled.
  • Contact the pro shop that drilled it, since warranty claims usually go through them.
  • Don’t attempt home repairs before checking the warranty, as that may void it.

A cracked ball isn’t always the end of the story, but prevention is easier. For how age and maintenance affect a ball more broadly, see how long does a bowling ball last?

The complete guide to ball construction

Bowling Ball Anatomy: Cores, Coverstocks and How They Shape Ball Reaction
Read the guide

Keep exploring

Guides from other topics

All topics →