Drilling and Layouts

Plugging and Redrilling a Bowling Ball: Weight Holes, Balance Holes and Extra Holes

Why and how bowling balls are plugged and redrilled, how many times it can be done, USBC balance hole rules, weight hole plugging and what extra holes count.

On this page
  1. Why Bowlers Plug and Redrill
  2. How Plugging Works
  3. How Many Times Can a Ball Be Plugged and Redrilled?
  4. Does Plugging Change How the Ball Reacts?
  5. Weight Holes and Balance Holes
  6. Extra Holes: What Counts
  7. How Much Weight Does Drilling Remove?
  8. Cost
  9. Can You Redrill a Ball for More Hook?

Why Bowlers Plug and Redrill

Plugging fills existing holes so the ball can be drilled again. Common reasons:

  • Your hand changed. Span, finger size and flexibility change over time, especially when moving from a conventional to a fingertip grip.
  • Your game changed. A new release, more revs or a switch to two-handed bowling can call for a different layout.
  • You bought a used ball. The previous owner’s holes almost never fit your hand.
  • You want a different reaction. A ball that hooks too early or too late may be worth a new layout.
  • Rules compliance. For example, a no-thumb bowler with both an unused thumb hole and a balance hole needs to plug one of them.
  • Damage. Cracks around a thumb hole are sometimes repairable by plugging and redrilling.

How Plugging Works

The exact method varies by shop, but it usually looks like this:

  1. Drill out the old hole to a clean, slightly larger size so the plug material bonds well.
  2. Fill the hole with plug material. That’s usually a liquid resin that hardens, or a solid plug rod set in resin.
  3. Let it cure fully. Rushing this step can lead to soft or shrinking plugs.
  4. Cut and sand the plug flush with the ball’s surface.
  5. Re-lay out and redrill the new holes, which may overlap the plugged area.

Done well, a plug is solid and stable. Done poorly, or redrilled before the material has cured, plugs can crack, shrink or separate.

How Many Times Can a Ball Be Plugged and Redrilled?

There’s no fixed number. It depends on:

  • How close the old and new holes are to the core. Each redrill can remove more of the original shell. Drillers watch how close the new holes get to the weight block.
  • How much plug material ends up overlapping. Drilling through mostly plug material, especially at the thumb, can weaken the area.
  • Static balance. Each new set of holes changes the ball’s weight distribution, and it eventually may not be possible to keep the ball within USBC limits.

Many balls handle one or two plug-and-redrills without trouble. Beyond that, ask your driller whether it’s still worth it. Sometimes the cost of another redrill gets close to the value of the ball.

Does Plugging Change How the Ball Reacts?

Plug material isn’t the same density as the original ball, and a new layout changes where the holes sit relative to the core. So a redrilled ball rarely behaves exactly like a freshly drilled one with the same layout. In most cases the difference from the plug itself is small compared to the layout change. But it’s one reason drillers sometimes advise against plugging a ball repeatedly to chase small changes.

Weight Holes and Balance Holes

What the Rules Allow

A balance hole (also called a weight hole or extra hole) is a hole that isn’t used for gripping. Under USBC rules:

  • A ball can have only one balance hole.
  • Balance holes have size limits. A maximum diameter of 1 1/4 inches is commonly cited; check the current USBC specifications if you’re near the limit.
  • For bowlers who don’t put their thumb in the ball, an unused thumb hole counts as the balance hole.
  • The drilled ball must stay within USBC static balance requirements to be used in certified competition.

Balance Hole Placement

Balance holes were traditionally used for two purposes: bringing a drilled ball back into static balance, and fine-tuning reaction by removing mass in a particular spot relative to the PAP and core. Where the hole goes affects the ball’s mass distribution, and drillers have long used specific positions to strengthen or weaken the motion.

How much difference a balance hole makes depends heavily on the core. On many modern balls with strong cores, the effect is smaller than it once was. Many current layout systems are designed to get the desired reaction without a balance hole at all. If a driller recommends one, ask what it’s for and what the reaction would be without it.

Plugging a Weight Hole

People plug weight holes for a few reasons: to comply with the rules, to get rid of a hole that was added for an old layout, or as part of a full redrill. Plugging a weight hole changes the ball’s static balance and, in some cases, its reaction, so the driller should check the ball’s balance afterward.

Extra Holes: What Counts

USBC allows up to five gripping holes: one for each finger and one for the thumb, all for the same hand. You don’t have to use every finger hole on every delivery, but you must be able to show that all the gripping holes can be used at the same time with the same hand. Any hole beyond that, or any hole you can’t actually grip, is treated as a balance hole and falls under the one-balance-hole limit. Small vent holes for relieving suction in the thumb hole are a separate case covered in the USBC specifications.

For the full picture on gripping holes, see do you have to use the holes when bowling. For no-thumb drillings specifically, see thumbless bowling layouts.

How Much Weight Does Drilling Remove?

The weight block inside a bowling ball is called the core. Manufacturers build undrilled balls with some extra weight near the top (often called top weight) to offset the material that drilling removes. A drilled ball usually ends up a little lighter than its labeled weight, typically by a few ounces, depending on the hole sizes and depth. Your pro shop can weigh the ball after drilling if you want an exact figure.

Cost

Pro shops usually price plugging per hole, with the redrill charged separately or bundled in. Costs vary a lot by shop and region. For typical price ranges and what drives them, see our guide to how much it costs to have a bowling ball drilled.

Can You Redrill a Ball for More Hook?

Sometimes, within limits. A new layout can move a ball’s reaction earlier or later and change how sharply it turns. Layouts with lower drill angles and the pin in the high-flare range tend to make the ball read the lane sooner. Higher drill angles and pin-up layouts tend to create a later, sharper move. See our guide to bowling ball drilling layouts for how pin and mass bias placement work.

But a layout can’t turn a weak ball into a strong one. If you want significantly more hook, a surface change (making the cover duller) or a stronger ball usually does more than a redrill, and costs less than a ball that’s been plugged one time too many.

The complete guide to drilling and layouts

Bowling Ball Drilling Layouts: Pin Placement and Hole Positions Explained
Read the guide

Keep exploring

Guides from other topics

All topics →