Drilling and Layouts

The Dual Angle Layout System: Drill Angle, VAL Angle and Pin Buffer Explained

How the Dual Angle bowling layout system works: what drill angle, pin-to-PAP distance and VAL angle measure, how to read a layout like 50 x 4 1/2 x 40, and its limits.

On this page
  1. What the Dual Angle System Is
  2. The Reference Points and Lines
  3. Number 1: The Drill Angle
  4. Number 2: Pin-to-PAP Distance (“Pin Buffer”)
  5. Number 3: The VAL Angle
  6. Reading a Dual Angle Layout
  7. How the Numbers Work Together
  8. Symmetrical vs Asymmetrical Balls
  9. A Note on “Pin Buffer” in Other Systems
  10. Limits of the System

What the Dual Angle System Is

The Dual Angle layout system is a way of describing exactly where a bowling ball’s pin and mass bias sit relative to a bowler’s release. It’s credited to ball designer Mo Pinel and is widely used by pro shops and ball manufacturers.

A Dual Angle layout is written as three numbers:

Drill angle x Pin-to-PAP distance x VAL angle

For example: 50 x 4 1/2 x 40.

Because every measurement is taken from your own positive axis point (PAP), the same three numbers should produce a similar kind of motion for different bowlers, even though the holes end up in different spots on the ball. That’s the system’s main advantage over informal descriptions like “pin up” or “pin down.”

The Reference Points and Lines

Before the numbers make sense, you need four references:

  • PAP (positive axis point): the point your release makes the ball spin around. It’s measured for each bowler. See how to find your positive axis point.
  • Pin: the marker showing the top of the core.
  • Mass bias (PSA): the marker showing the direction of an asymmetrical core’s bias.
  • VAL (vertical axis line): a reference line drawn through the PAP, perpendicular to the midline that runs through your grip center and PAP. It splits the ball into a “grip side” and a “far side” of your axis.

If you’re not sure which marking is which, see what the colored dots on bowling balls mean.

Number 1: The Drill Angle

The drill angle is the angle at the pin between two lines: one from the pin to your PAP, and one from the pin to the mass bias. It runs from 0 to 180 degrees.

General effect:

Drill angle Typical motion
Low (roughly 10–45°) Earlier hook, smoother and more rounded
Medium (roughly 45–60°) Balanced, all-around
High (roughly 60–90°) Later hook, sharper and more angular

The drill angle is often described as the main control over how sharply the ball changes direction, especially on asymmetrical balls.

Number 2: Pin-to-PAP Distance (“Pin Buffer”)

The middle number is the distance from the pin to your PAP, in inches, measured across the ball’s surface. In many pro shops this is loosely called the “pin buffer.” It mainly controls how much the ball flares:

  • Around 3 3/8 inches is commonly cited as the maximum-flare position.
  • Closer to the PAP (under about 3 inches) reduces flare and gives a smoother, more controllable roll.
  • Farther from the PAP (about 5 inches and up) also reduces flare, and tends to add length.

Around 4 to 5 inches is a popular all-around range: strong flare without being at the maximum.

Number 3: The VAL Angle

The VAL angle relates the layout to the vertical axis line. In common descriptions, it’s the angle formed where a line from the pin, extended through the ball’s center of gravity area, crosses the VAL. Different manuals illustrate the construction slightly differently, so if you’re doing the measuring yourself, follow the diagram for the system your driller uses.

General effect:

  • Lower VAL angles tend to produce an earlier, smoother transition from skid to hook.
  • Higher VAL angles tend to delay the transition and make the backend reaction stronger.

The VAL angle is a finer adjustment than the drill angle. Many bowlers can feel a big drill angle change more easily than a VAL angle change.

Reading a Dual Angle Layout

Take 50 x 4 1/2 x 40:

  • 50° drill angle: middle-of-the-road, slightly toward the smoother side of center
  • 4 1/2 inches pin-to-PAP: strong flare, just past the maximum-flare position
  • 40° VAL angle: a moderate transition

That describes a balanced, versatile layout. By contrast, something like 70 x 5 x 60 would generally aim for a longer, more angular reaction, and 30 x 4 x 30 for an earlier, smoother one.

How the Numbers Work Together

The three numbers are related. Change one and the others may need to move to keep the holes on the ball sensibly. Some combinations also put the mass bias or holes in awkward places. In practice:

  • Drillers usually start with the reaction shape they want (early and smooth vs late and angular) and pick a drill angle to match.
  • Next they choose a pin-to-PAP distance for the amount of flare.
  • Then they use the VAL angle to fine-tune timing.

They also check that the result keeps the drilled ball within USBC static balance limits, sometimes without a balance hole and sometimes with one. For how layouts relate to oil conditions, see layouts for heavy oil and dry lanes.

Symmetrical vs Asymmetrical Balls

The system was built with asymmetrical cores in mind, where the mass bias is a real, separate direction. On symmetrical balls there’s no meaningful mass bias, so the drill angle and VAL angle matter less. Layouts for symmetrical balls are often described mainly by pin-to-PAP distance and pin height relative to the fingers.

A Note on “Pin Buffer” in Other Systems

The term “pin buffer” isn’t used consistently. In Storm’s VLS (Value Layout System), “pin buffer” refers to the pin’s distance from the VAL, not its distance from the PAP. If a layout sheet lists a “pin buffer,” check which system it’s written in. Mixing the two up can put the pin in the wrong place.

Limits of the System

The Dual Angle system is precise, but it has limits:

  • Your PAP has to be right. A wrong PAP measurement throws off every number.
  • Coverstock matters more. Many coaches consider the cover and surface the biggest influence on ball reaction. Layout fine-tunes the shape.
  • Small differences are hard to feel. Unless you’re very consistent, you may not notice a 5- or 10-degree change.
  • It describes the core, not the fit. Span, pitch and hole size are a separate job. See how your hand should fit a bowling ball.

For the bigger picture on pin and mass bias placement, see our guide to bowling ball drilling layouts.

The complete guide to drilling and layouts

Bowling Ball Drilling Layouts: Pin Placement and Hole Positions Explained
Read the guide

Keep exploring

Guides from other topics

All topics →