Drilling and Layouts

How to Find Your Positive Axis Point (PAP) and Measure Pin-to-PAP Distance

Step-by-step guide to finding your bowling PAP from the oil track, confirming it, recording it as over and up, and measuring pin-to-PAP distance for layouts.

On this page
  1. What the PAP Is
  2. Why Your PAP Matters
  3. What You Need
  4. Step-by-Step: Finding Your PAP
  5. Confirming Your PAP
  6. Recording Your PAP: Over and Up
  7. Measuring Pin-to-PAP Distance
  8. Common Mistakes
  9. Two-Handers and No-Thumb Bowlers
  10. Why Your PAP Can Change

What the PAP Is

When a bowling ball rolls down the lane, it spins around an axis. That axis meets the ball’s surface at two points. The one you can see during the shot, on the side of the ball toward your bowling hand, is the positive axis point (PAP). The opposite point is the negative axis point, which isn’t used in layouts.

For right-handers, the PAP is to the right of the grip. For left-handers, it’s to the left.

Your PAP reflects your release: in particular, your axis rotation (how much your hand turns the ball sideways at release) and your axis tilt (how tilted the spin is). That’s why two bowlers with similar grips can have quite different PAPs, and why changing your release can move it.

Why Your PAP Matters

Every layout is measured from your PAP. When a driller says “pin 4 inches from your PAP,” they mean your PAP. Two bowlers with different PAPs who drill the same ball with the same pin position on the shell can get noticeably different reactions.

Knowing your PAP lets a pro shop place the pin and mass bias deliberately, rather than guessing. For how those placements change ball motion, see our guide to bowling ball drilling layouts.

What You Need

  • A ball you can throw consistently (a lower-flare ball, such as a plastic or mild reactive ball, makes the track easier to read)
  • A wax or grease pencil
  • A small piece of tape or a small sticker
  • A flat surface such as a table, a ball cup, or a ball ring to rest the ball on
  • A flexible ruler or tape measure (a dedicated layout tool, such as an Armadillo, is even better)

Step-by-Step: Finding Your PAP

  1. Throw a normal shot. Use your usual speed and release. Wipe the ball clean first so the new track is easy to see.
  2. Find the first oil ring. When the ball comes back, you’ll see one or more rings of oil. If the ball flared, there will be several. Look for the ring closest to your finger and thumb holes. That’s the track from the first part of the shot, before flare and hook took over.
  3. Trace that ring. Mark along the edge of that ring with the wax pencil.
  4. Set the track as an “equator.” Rest the ball so the traced line runs level and parallel to the table all the way around, like the equator on a globe.
  5. Mark the top. The point at the very top of the ball, the “north pole” of that equator, is your approximate PAP. Put a small piece of tape there.

With a layout tool, the process is faster and more accurate. You line the tool up with the traced track and mark the PAP at the point it indicates.

Confirming Your PAP

Throw the ball again with the tape on your estimated PAP. Watch the tape just after release:

  • If the tape stays almost still, spinning in place for the first part of the shot, you’re close.
  • If the tape wobbles in a circle, the mark is off. Re-trace a fresh track and try again.

Repeat a few times. Your release isn’t identical every shot, so you’re looking for your typical PAP, not one perfect shot.

Recording Your PAP: Over and Up

PAP is usually recorded relative to your grip center, the midpoint between your thumb hole and finger holes along the line through the middle of your grip.

  1. Draw a line through the center of your thumb hole and the middle of the bridge between your finger holes. That’s your midline.
  2. Measure horizontally from the grip center along that line toward your PAP side. That’s “over.”
  3. Measure vertically, perpendicular to that line, to the PAP. That’s “up” (above the line, toward the fingers) or “down” (below it).

You’ll end up with something like “5 inches over, 1/2 inch up.” Many one-handed bowlers fall in the range of roughly 4 to 6 inches over, but there’s a lot of variation, so measure rather than assume.

Measuring Pin-to-PAP Distance

Once you know your PAP, measuring the pin-to-PAP distance is simple:

  1. Locate the pin, the colored dot that marks the top of the core. If you’re not sure which mark it is, see what the colored dots on bowling balls mean.
  2. Measure the straight-line distance across the ball’s surface from the center of the pin to your PAP mark, using a flexible ruler.

As a rough guide, about 3 3/8 inches is commonly cited as the position with the most flare potential. Distances well under or well over that tend to reduce flare. Pin-to-PAP distance is the middle number in the Dual Angle layout system, which our Dual Angle layout explainer covers in detail.

Common Mistakes

  • Tracing the wrong ring. Only the ring nearest the grip shows your initial axis. Later rings show flare migration.
  • Using a high-flare ball. Multiple overlapping rings make it hard to pick the right one.
  • Measuring after an unusual shot. Use your normal shot, and check several.
  • Not cleaning the ball first. Old oil lines confuse the reading.
  • Measuring from the wrong reference. Make sure you know where your grip center is, especially if you bowl without a thumb.

Two-Handers and No-Thumb Bowlers

If you don’t put your thumb in the ball, your grip center moves to the middle of the bridge between your finger holes. Measure your PAP from there. Two-handed releases often produce a lot of axis rotation, so their PAPs can sit in quite different positions from a typical one-hander’s. See thumbless bowling layouts for more.

Why Your PAP Can Change

Your PAP isn’t permanent. It can shift if you:

  • Change your release or hand position
  • Switch grips (for example, conventional to fingertip)
  • Get a new fit with a different span or pitch
  • Get tired late in a set, or adjust your hand position for different lane conditions

It’s worth re-checking your PAP every so often, especially before drilling a new ball. Many pro shops will measure it for you, often at no or little cost.

The complete guide to drilling and layouts

Bowling Ball Drilling Layouts: Pin Placement and Hole Positions Explained
Read the guide

Keep exploring

Guides from other topics

All topics →