Bowling pin specs at a glance
Regulation ten-pin bowling pins are built to tight specifications set by the United States Bowling Congress (USBC) and World Bowling. The headline numbers:
| Spec | Regulation tenpin |
|---|---|
| Height | 15 inches (about 38 cm) |
| Widest point (the belly) | about 4.766 inches (about 12.1 cm) |
| Base diameter | about 2.03 inches (about 5.2 cm) |
| Weight | 3 lb 6 oz to 3 lb 10 oz (about 1.53 to 1.64 kg) |
| Spacing | 12 inches center to center |
Pins in a single set are also expected to be closely matched in weight, so one pin isn’t noticeably heavier than its neighbors. The full specifications, including the exact profile at every height, are in USBC’s equipment manual.
What bowling pins are made of
A standard tenpin is made of hard maple. The wood is glued up from several blocks rather than carved from one solid piece, then turned on a lathe to shape. The wooden core is coated with a tough plastic layer, usually nylon or Surlyn, that protects it from ball impact and gives the pin its glossy white finish. The neck stripes, the maker’s logo and the approval stamp are added on top.
Fully synthetic pins also exist and are approved for certified play. Pins used on string pinsetters have a fitting at the top for the cord. For the companies that make them, see who makes bowling pins.
The 10-pin setup: rows and numbering
The ten pins stand in four rows, forming an equilateral triangle that points toward the bowler. They’re numbered left to right, front to back, as seen from the approach:
7 8 9 10
4 5 6
2 3
1
- Row 1: the 1 pin
- Row 2: the 2 and 3 pins
- Row 3: the 4, 5 and 6 pins
- Row 4: the 7, 8, 9 and 10 pins
Every center uses this numbering. It’s how bowlers describe leaves (“I left the 3-10”) and how the scoring screen shows standing pins.
The head pin (front pin)
The 1 pin at the front of the triangle is called the head pin. It’s the pin closest to the bowler and the first one most strike balls touch. Hitting the head pin full on (a “nose hit”) often leaves splits, because the ball deflects without driving through the middle of the rack.
The kingpin, corner pins and the pocket
- The 5 pin sits in the middle of the rack and is often called the kingpin. A ball that reaches it with enough angle has a good chance of carrying a strike.
- The 7 and 10 pins are the back corners. They’re the two hardest single-pin spares for many bowlers, and the 7-10 split is the most famous difficult leave in bowling.
- The pocket is the gap between the head pin and the pin beside it on your hook side: the 1-3 pocket for right-handers and the 1-2 pocket for left-handers. Research on strike carry has found that the ideal strike ball for a right-hander contacts only the 1, 3, 5 and 9 pins, with the other pins falling as they knock into each other.
Pin spacing and why it matters
Neighboring pins are 12 inches apart, center to center. The gap between two pins’ widest points is about 7.2 inches. A regulation ball is about 8.5 inches in diameter, so it can reach two side-by-side pins at once, but it can’t touch all ten pins on its own. Strikes depend on pins knocking other pins down.
The pin spots on a certified lane’s pin deck are marked and measured during lane certification, and the pinsetter sets each pin back on its own spot every frame.
What is the “diamond” configuration?
Ten-pin bowling uses a triangle, not a diamond. The diamond comes from ninepin bowling (kegeln), popular in Germany and parts of Europe, where nine pins stand in a diamond (a square turned 45 degrees). Tenpin bowling grew out of ninepins in the 1800s, which is why people sometimes describe the rack as a diamond.
In ten-pin, “diamond” also sometimes describes a four-pin leave in a diamond shape: the 2-4-5-8 for right-handers or the 3-5-6-9 for left-handers, more commonly called a bucket.
How to set up 10 pins by hand
For a home, backyard or toy set:
- Mark the spot for the 1 pin at the front.
- Place the 2 and 3 pins in the next row, each half a pin-spacing to the left and right of the 1 pin and one row back.
- Place the 4, 5 and 6 in the third row, with the 5 directly behind the 1.
- Place the 7, 8, 9 and 10 in the back row.
- Keep the spacing equal everywhere. On a regulation layout that’s 12 inches between centers and about 10.4 inches between rows.
For scaled-down sets, keep the same triangle and scale the spacing to the size of the pins. If the pins are touching, they’re too close.
Other pin types compared
- Duckpins: shorter and squatter, used with small, hand-held balls and three rolls per frame
- Candlepins: tall, thin and symmetrical end to end, used mainly in New England and parts of Canada
- Five-pins: a Canadian game with five pins in a V, each pin with a rubber band around its belly
- Ninepins: used in the diamond layout described above, usually on string pinsetters
Not to be confused with the “pin” on a bowling ball
You’ll often hear “pin up,” “pin down” or “pin distance” in conversations about bowling balls. Those have nothing to do with bowling pins. On a ball, the pin is a small colored dot marking where the top of the ball’s core sits. Where the pin is placed relative to your finger holes is part of a ball’s layout, and it affects how the ball hooks. A pro shop can explain which layout suits your game.