Scoring and Formats

Five-Pin Bowling: Setup, Rules and How to Grip the Ball

Five-pin bowling explained: the V-shaped pin setup and point values, three balls per frame, how scoring reaches 450, and how to grip a ball with no holes.

On this page
  1. Yes, five-pin bowling is a real game
  2. How five-pin is set up
  3. Rules of play
  4. Scoring example
  5. How to grip a five-pin ball
  6. Delivery basics
  7. Common beginner mistakes
  8. Five-pin vs ten-pin at a glance

Yes, five-pin bowling is a real game

Five-pin bowling is a variation of bowling played mostly in Canada, where it’s a staple of bowling centres, youth programs and leagues. It’s generally credited to Thomas F. Ryan, who ran a bowling club in Toronto and introduced the game around 1909 as a lighter, quicker alternative to ten-pin.

The basics:

  • Five pins set in a V, each worth a different number of points.
  • A small, hand-held ball with no finger holes.
  • Three balls per frame, ten frames per game.
  • A perfect game of 450.

How five-pin is set up

The pins and their values

The five pins are set in a V shape pointing toward the bowler, with the headpin at the front centre. From left to right, as the bowler sees them:

Position Pin Points
Far left Left corner pin 2
Left Left three pin 3
Centre (front) Headpin 5
Right Right three pin 3
Far right Right corner pin 2

That’s 15 points for a full rack. The pins are smaller than ten-pins, and each has a rubber band around its middle, which helps the pins kick and scatter when hit.

When people ask “how many pins are in a set?” for five-pin, the answer is five per lane, though centres keep spares to swap in as pins wear.

The ball

A five-pin ball is small enough to sit in the palm of an adult’s hand and has no finger holes. Under Canadian rules it’s limited to roughly 5 inches in diameter and a little under 4 pounds (3 lb 10 oz is the usual maximum). Balls are typically made of rubber or similar hard material. Because there are no holes, there’s no drilling or fitting, and there’s no question of interchangeable finger grips: everyone holds the same kind of ball.

The lane

Five-pin is played on lanes similar in length and width to ten-pin lanes, with a foul line, gutters and an approach. The difference is at the pin end: the pinsetter is set up for five pins in the V, and centres usually have dedicated five-pin lanes rather than converting ten-pin lanes night by night.

Rules of play

Three balls per frame

Each bowler gets up to three balls per frame to knock down all five pins. A game is ten frames. Fallen pins are cleared between balls, so you’re always aiming at whatever is still standing.

Strikes, spares and the 10th frame

  • Strike: all five pins on the first ball. Worth 15 plus the points from your next two balls.
  • Spare: all remaining pins cleared with the second ball. Worth 15 plus the points from your next ball.
  • Clearing with the third ball: worth 15, with no bonus.
  • Open frame: pins still standing after three balls. You score the point values of the pins you knocked down.

In the 10th frame, a strike earns two more balls and a spare earns one, so the bonuses can be completed. A perfect game is twelve strikes: 12 balls, each frame worth 45, for 450.

If you already know ten-pin, the bonus logic is identical. Our guide to how ten-pin bowling scoring works explains the idea in more detail; five-pin just counts points instead of pins.

Fouls

As in ten-pin, stepping over the foul line during delivery is a foul, and the pins knocked down by that ball don’t count. League and tournament play follows rules set by the Canadian five-pin governing body, so check with your centre for the finer points.

Scoring example

Here are the first three frames of a game:

Frame Balls Frame value Running total
1 Strike 15 + 10 + 5 = 30 30
2 10 (headpin, three and corner on the left), then 5 (the right three and corner) for a spare 15 + 13 = 28 58
3 13 (all but a corner pin), miss, then 2 on the third ball 15 73

Frame 1’s strike picks up the 10 and 5 from frame 2. Frame 2’s spare picks up the 13 from frame 3’s first ball. Frame 3 is cleared on the third ball, so it’s worth 15 with no bonus.

How to grip a five-pin ball

With no holes to fit your fingers into, the grip is about holding the ball securely while letting it roll off your hand smoothly.

Palm-and-fingers hold

Most bowlers cradle the ball in the palm with the fingers spread comfortably underneath and along the side. The ball should feel secure without squeezing. A death grip tends to make the release jerky and pulls the ball off line.

Smaller hands, including kids, often hold the ball more in the fingers than the palm. That’s fine as long as the ball doesn’t slip during the swing.

Where the thumb goes

The thumb usually rests lightly on the side or top of the ball to steady it. It shouldn’t be pressing hard. Think of it as a guide that comes off the ball naturally at release.

Adding spin

Many five-pin bowlers throw a fairly straight ball, which is a sensible place to start. Once you’re consistent, you can add a little curve by turning the hand slightly at release so your fingers come up the side of the ball, similar to the motion of shaking hands. Small adjustments go a long way with a ball this light.

Delivery basics

  • Stance: stand facing the pins, ball held at about waist height, weight balanced.
  • Approach: many bowlers use three to five steps. Beginners can start with a simpler one- or two-step delivery.
  • Swing: let the arm swing like a pendulum. Because the ball is light, it’s easy to muscle it; try to let the swing do the work.
  • Release: roll the ball onto the lane past the foul line rather than dropping or lofting it.
  • Target: with only five pins, aim matters. Many bowlers aim to hit the headpin slightly to one side so the ball drives through a three pin as well.

Common beginner mistakes

  • Throwing too hard. Speed helps a little, but accuracy matters much more with widely spaced pins.
  • Gripping too tightly, which causes the ball to come off the hand unevenly.
  • Ignoring the corner pins. Leaving a 2-pin standing after the first ball is common; picking it up consistently is a big part of scoring well.
  • Lofting the ball, which can bounce it off line and isn’t kind to the lane.

Five-pin vs ten-pin at a glance

Five-pin Ten-pin
Pins 5, in a V 10, in a triangle
Pin values 2, 3, 5, 3, 2 1 point each
Ball Small, no holes Larger, drilled with finger holes
Balls per frame Up to 3 Up to 2
Perfect game 450 300
Where it’s common Canada Worldwide

Five-pin isn’t the only small-ball game. Duckpin bowling, played mainly in the eastern US, also uses a holeless ball and three balls per frame, but with ten pins in a triangle. For more on the jargon you’ll hear in any of these games, see our list of common bowling slang terms.

The complete guide to scoring and formats

How Bowling Scoring Works: Frames, Strikes and Spares
Read the guide

Keep exploring

Guides from other topics

All topics →