Lanes and Machines

How Bowling Pinsetters Work

How a bowling pinsetter clears deadwood, respots standing pins, sorts pins from the ball in the pit and sets a fresh rack, with AMF and Brunswick models compared.

On this page
  1. What a pinsetter does
  2. The main parts of a pinsetter
  3. The first-ball cycle, step by step
  4. The second-ball and strike cycle
  5. How the machine gets pins back into a rack
  6. AMF vs Brunswick: the main machine families
  7. Free-fall vs string machines
  8. Why pinsetters jam or stop
  9. A short history: from pin boys to machines
  10. Safety note

A pinsetter is the machine behind the pins that clears fallen pins, puts standing pins back where they were, sets a fresh rack of ten for each frame, and sends your ball back to you. Brunswick calls its machines pinsetters and AMF calls its machines pinspotters. They do the same job.

This article explains how a traditional free-fall pinsetter works, the kind most bowling centers have used since the 1950s. It also covers how the main machine families differ and why these machines sometimes stop mid-game.

What a pinsetter does

Every pinsetter has three jobs:

  1. Clear deadwood. Fallen pins have to be removed from the pin deck before your next ball.
  2. Respot standing pins. After your first ball, any pins still standing must be lifted out of the way and set back down on exactly the same spots.
  3. Set a new rack. After a strike or a second ball, the machine sets a full triangle of ten pins.

It also separates the ball from the pins in the pit and passes the ball to the ball return.

The main parts of a pinsetter

The exact design varies by manufacturer, but nearly every free-fall machine has these parts:

  • Sweep bar (rake): a bar that drops across the front of the pin deck. It guards the machine from a second ball rolled too early and pushes fallen pins back into the pit.
  • Setting table (deck): a frame above the pin deck with ten positions. It lowers to grip or lift standing pins and to set new racks.
  • Pit: the lowered area behind the pin deck where the ball and fallen pins land, with a cushion or curtain at the back to stop them.
  • Pit conveyor or carpet: a moving belt on the pit floor that carries the ball and pins toward the rear of the machine.
  • Pin elevator: usually a large rotating wheel or lift at the back that raises pins to the top of the machine.
  • Pin distributor or turret: the part that feeds pins one by one into the table’s ten storage spots so a full rack is waiting.
  • Ball lift or accelerator: moves the ball out of the pit and into the return track.
  • Sensors and controller: detect the ball, track the frame and, on many machines, report standing pins to the scoring system.

The first-ball cycle, step by step

Here’s what happens after your first ball on a typical free-fall machine:

  1. Trigger. The ball reaches the pit, or passes a sensor near the pin deck, and the machine starts its cycle. Many machines wait a few seconds after the ball arrives so pins have time to stop wobbling.
  2. Sweep drops. The sweep bar lowers to its guard position at the front of the deck.
  3. Table descends. The setting table comes down over the pins. Gripping cells or tongs close around the neck of each pin that’s still standing.
  4. Pins are read. On many machines this is when standing pins are detected, mechanically or by a camera, and sent to the scorer. See how automatic scoring detects fallen pins.
  5. Standing pins lift. The table rises with the standing pins held above the deck.
  6. Sweep clears. The sweep pushes everything left on the deck (the deadwood) back into the pit, then returns to its guard position.
  7. Pins respotted. The table lowers again and releases the standing pins onto their original spots.
  8. Ready. The table and sweep lift out of the way, and you can throw your second ball.

The second-ball and strike cycle

After a second ball, or after a strike, nothing has to be saved. The sweep drops and clears the deck completely. Then the table, already loaded with ten pins from storage, comes down and sets a fresh rack. Modern controllers often run a shorter cycle when it makes sense. On a strike, for example, there is nothing to lift and respot.

How the machine gets pins back into a rack

In the pit, the ball and pins land together, and the machine has to separate them:

  • On AMF 82-series pinspotters, a continuously running carpet belt carries the ball and pins to the rear. The heavier ball is pushed off to the side, where it enters the ball lift. The pins pass under the cushion into a ring-shaped rotating elevator that lifts them to the top. A distributor then travels over the table and drops each pin into an empty spot.
  • On Brunswick A-series machines (Model A, A2, JetBack), a shaker board feeds pins and ball toward two wheels at the back. The ball rides up on the ball wheel, while the narrower pins drop through to a pin wheel. Pins go up into a rotating turret that fills its ten spots, then drops all ten into the table at once.
  • On Brunswick GS-series machines (GS-X and the newer GS-NXT), a belt on the pit floor moves pins to a vertical elevator, and the ball leaves through a side door into an under-lane accelerator.

A free-fall machine usually holds around 20 pins in circulation, so a complete rack is already waiting while the last rack is still on the deck.

AMF vs Brunswick: the main machine families

Family Maker Notes
AMF 82-30 AMF (now QubicaAMF) Mass-produced from the 1950s–60s; no longer made, but some are still running
AMF 82-70 AMF (now QubicaAMF) Introduced in the 1960s; one of the most common machines in the world
AMF 82-90 / 82-90XLi QubicaAMF Based on the 82-70 mechanics with updated electronics and controls
Brunswick A / A2 / JetBack Brunswick Recognizable by the turret and the metal deck shield in front of the table
Brunswick GS series Brunswick GS-10 through GS-X; the GS-NXT is a lower-profile update

If you’re shopping for machines, our guide to what a pinsetter machine costs compares new, used and string options.

Free-fall vs string machines

Everything above describes free-fall machines, where pins are loose and fly freely when hit. String pinsetters tie a cord to the top of each pin. After each ball they reel all the pins up, then lower the ones that were standing. They need far fewer parts, but the cords affect how pins scatter. See string pinsetters: how pins on strings change bowling.

Why pinsetters jam or stop

Free-fall machines have many moving parts, and a few problems come up again and again:

  • Off-spot pins: a pin slides partway off its spot but stays standing, and the table can’t grip it cleanly.
  • Pin jams: a pin turns sideways in the elevator, distributor or turret.
  • Ball stuck in the pit: the ball doesn’t reach the ball lift, so the return never comes.
  • Short rack: the storage system hasn’t filled all ten spots, so the machine waits before setting the new rack.

When a machine stops, bowlers usually press a reset or call button at the console, and a staff mechanic clears the jam.

A short history: from pin boys to machines

Before automatic machines, centers hired “pin boys” to reset pins and roll balls back by hand. Gottfried (Fred) Schmidt developed the first workable automatic pinsetter, and AMF bought his patent and introduced its production machine in 1952. Brunswick followed a few years later. The machines made bowling faster and cheaper to run and helped drive the sport’s boom in the late 1950s and 1960s.

Safety note

Pinsetters are heavy industrial machines with powerful moving parts. Bowling center staff have been seriously injured and killed while clearing jams in running or unsecured machines. Bowlers should never walk down the lane or reach into a pinsetter. Use the call button and let trained staff deal with it.

The complete guide to lanes and machines

How a Bowling Alley Works: Lanes, Pins, Pinsetters and More
Read the guide

Keep exploring

Guides from other topics

All topics →