Spares

Can You Pick Up the 7-10 Split? Odds and Technique

Yes, the 7-10 split can be converted, but very rarely. Learn why it's so hard, how bowlers attempt it, and when to take one pin instead.

On this page
  1. Why the 7-10 is so hard
  2. What are the odds?
  3. How bowlers try to convert the 7-10
  4. Should you try for both pins?
  5. How to avoid leaving the 7-10
  6. Other splits that are more makeable

Yes, the 7-10 split can be picked up, but it’s one of the rarest conversions in bowling. Because the two pins are so far apart, the ball can’t hit both. The only way to convert is to send one pin across the pin deck into the other, which takes a nearly perfect shot and a fair amount of luck. For most bowlers in most situations, the smarter play is to take one pin.

Why the 7-10 is so hard

The 7 and 10 are the back corner pins, on opposite edges of the lane. Pins in the same row are set 12 inches apart, center to center, so the 7 and 10 are about 36 inches apart. A bowling ball is only about 8.5 inches wide, so there’s no line where the ball can touch both.

That leaves pin-to-pin action as the only option: knock one corner pin hard enough, at exactly the right angle, that it travels roughly three feet across the deck and takes out the other. The window for that is extremely small.

The leave is nicknamed the bedposts or goalposts. You can find more split names in our guide to bowling pin leave and split names.

What are the odds?

Very low. Commonly cited estimates put the conversion rate well under 1%, even for professional bowlers, and many experienced league bowlers go years without making one.

At the highest level it’s rare enough to be a headline. Mark Roth is widely credited with the first 7-10 conversion on a televised PBA event, in 1980, and only a handful of televised conversions have been recorded since. For comparison, professionals convert most single-pin spares almost every time.

How bowlers try to convert the 7-10

There are two main ideas. Both require hitting one pin on a specific edge with good speed.

The thin hit across the deck

The goal is to hit one corner pin on its outside edge — the side nearest the channel — so thinly that the pin shoots almost sideways across the pin deck into the other corner pin. The ball barely grazes the pin and continues on, while the pin does the work.

  • Hitting too much of the pin sends it backward into the pit instead of across.
  • Missing by even a little sends the ball into the channel, which scores the same as any other miss.
  • Extra speed tends to help the pin travel farther, but it also makes the shot harder to control.

The kickback rebound

The other idea is to hit a corner pin on its inside edge so it flies hard into the kickback (the side wall next to the pin deck) and rebounds across the lane toward the other pin. This depends heavily on the angle and how lively the kickbacks are, so it’s even less predictable.

Which pin to go for

There’s no universal answer. Some bowlers go for the pin their ball naturally moves toward, so a hook can help create the thin hit. Others pick the side where they have their most reliable corner-pin line. If you do try, choose one approach and stick with it, so you learn from each attempt.

Should you try for both pins?

Usually not. Think about what’s at stake:

  • Taking one pin is a fairly high-percentage shot if you have a solid corner-pin line. That gives you a count of 9 for the frame instead of 8.
  • Going for both risks missing everything for a count of 8, in exchange for a very small chance of a spare.

In most league and tournament situations, that extra pin is worth more on average than the slim chance of converting. Many coaches advise taking the sure pin unless you need the spare to win — for example, late in a close match where only a spare will do.

If you’re taking one pin, use your normal spare line for it:

How to avoid leaving the 7-10

The 7-10 most often appears after a ball hits the head pin too full or “high,” which sends the front pins straight back and leaves both back corners standing. It can also follow a weak or flat hit where the ball deflects too much. There’s no way to avoid it completely, but more consistent pocket hits make it less common.

Strike ball adjustments are outside the scope of this guide, but in general, if you’re leaving the 7-10 repeatedly, your ball may be entering the pins too straight or too far into the head pin. A small move in your feet or target, or a coach’s eye on your strike line, can help.

Other splits that are more makeable

The 7-10 gets the attention, but many splits are realistic targets for a good spare shooter:

  • Baby splits (2-7 and 3-10): the pins are close enough for the ball to hit both.
  • Baby split with company (2-7-8 and 3-9-10): similar, with an extra pin that’s usually taken out on the same line.
  • 4-5 and 5-6: pins side by side in the same row, close enough for the ball to cover both.

Wider splits like the 4-6, 4-10 or 6-7 sit in between — hard, but more makeable than the 7-10. For a full approach to spares and splits, including how to find the key pin and choose a line, see our guide to spare alignment and the 3-6-9 system.

The complete guide to spares

How to Pick Up Spares: Alignment and the 3-6-9 System
Read the guide

Keep exploring

Guides from other topics

All topics →