Drilling and Layouts

Thumbless Bowling Layouts for Two-Handed and No-Thumb Bowlers

How thumbless layouts work for two-handed and no-thumb bowlers: grip center, PAP measurement, USBC balance hole rules and layout ideas for high-rev releases.

On this page
  1. What a Thumbless Layout Is
  2. Do Two-Handed Bowlers Use Their Thumb?
  3. What Changes Without a Thumb Hole
  4. USBC Rules for No-Thumb Bowlers
  5. Layout Considerations for Two-Handers
  6. Finger Hole Fit for No-Thumb Grips
  7. One-Handed No-Thumb Bowlers
  8. Switching Between Thumb In and Thumb Out
  9. Getting Started

What a Thumbless Layout Is

A thumbless layout is a drilling for a bowler who doesn’t put their thumb in the ball. Usually the ball has only finger holes, typically for the middle and ring fingers. The bowler is most often a two-hander, but some one-handed bowlers also go thumbless.

Without a thumb in the ball, the hand sits differently, the release produces a different axis of rotation, and the rules on extra holes work differently. All of that changes how the ball should be laid out.

Do Two-Handed Bowlers Use Their Thumb?

Most two-handed bowlers don’t put their thumb in the ball on strike shots. The non-bowling hand supports the ball through the swing, and the bowling hand stays in the finger holes only. Some two-handers do put their thumb in for spare shots and roll the ball one-handed. That has rule implications, covered below.

What Changes Without a Thumb Hole

The Grip Center Moves

On a three-hole ball, the grip center (the reference point for measuring layouts) sits between the thumb hole and the finger holes. Without a thumb, the reference point moves to the center of the bridge between the finger holes. Every layout measurement is taken from there.

Measuring the PAP

Your positive axis point is still the starting point for the layout. It’s just measured from the bridge instead of the traditional grip center. Two-handers often have high rev rates and a lot of axis rotation, so their PAP and track can look quite different from a typical one-hander’s. A pro shop should measure it rather than guess. Our guide on how to find your positive axis point covers the method, including the two-handed grip-center difference.

Static Balance

With no thumb hole, less material comes out of the ball, and it comes out in a different place than on a three-hole drilling. The drilled ball still has to fall within USBC static balance limits for certified competition, so the driller has to account for that when choosing the layout.

USBC Rules for No-Thumb Bowlers

USBC modified its gripping-hole rule specifically because of no-thumb bowlers. Under the current wording:

  • A thumb hole you don’t use for gripping counts as a balance hole.
  • A ball can have only one balance hole. So a no-thumb bowler’s ball can have either an unused thumb hole or a balance hole, but not both.
  • If a ball has an unused thumb hole and a separate balance hole, at least one has to be plugged before it can be used in certified competition.
  • Resting your palm over an empty thumb hole doesn’t count as gripping it.

USBC’s stated reasoning was fairness: without the rule, a no-thumb bowler could effectively get two balance holes and extra layout options not available to bowlers who use their thumb. Rules can change, so check USBC’s current equipment specifications or ask your league if you’re unsure. For more on which holes you have to use, see do you have to use the holes when bowling. If an older ball now has one hole too many, see plugging and redrilling a bowling ball.

Layout Considerations for Two-Handers

Because many two-handers generate a lot of revs, layout often focuses on controlling the reaction rather than adding to it. Common considerations:

  • Taming early hook. High-rev releases can make a strong ball read the lane too early. Layouts that add length, such as higher drill angles, the pin farther from the PAP, or pin-up placements, are often used to delay the motion.
  • Managing flare. Layouts with the pin near the high-flare zone (around 3 3/8 inches from the PAP) can be a lot for a high-rev player on drier lanes. Pins closer to or farther from the PAP reduce flare.
  • Smoothing the backend. Lower drill angles produce a more rounded, arcing motion, which some two-handers prefer for control on house patterns.

These are general directions. Two-handed releases vary a lot, and what suits one player may be too much or too little for another. Your driller should base the layout on your measured PAP, your speed and revs, and the conditions you bowl. For a general walkthrough of the layout levers, see our guide to bowling ball drilling layouts. For layout choices by oil level, see layouts for heavy oil and dry lanes.

Finger Hole Fit for No-Thumb Grips

Without a thumb to anchor the ball, the finger holes carry more of the grip. Things drillers commonly adjust:

  • Hole size: snug enough to stay secure through the swing without needing to squeeze
  • Pitch: the angle of the finger holes affects how securely they hold and how cleanly they release. See our guide to forward, reverse and lateral pitch.
  • Inserts: many no-thumb bowlers use finger inserts for a consistent feel
  • Depth: some two-handers insert their fingers deeper than a classic fingertip grip

Bowlers on three-hole balls often use tape in the thumb hole to fine-tune fit as their thumb swells or shrinks. No-thumb bowlers make the same kind of adjustment in the finger holes, typically with tape or by changing inserts.

One-Handed No-Thumb Bowlers

Some one-handed bowlers also release without the thumb, sometimes after a thumb injury. The same rules apply (an unused thumb hole counts as a balance hole), and the grip center is the bridge. One-handed no-thumb releases tend to be less predictable than two-handed ones, so it’s worth having a pro shop watch you bowl before choosing a layout.

Switching Between Thumb In and Thumb Out

If you use your thumb on some shots (often spares) and not on others, USBC expects the ball to be within specifications from both grip centers: the middle of the grip with the thumb in, and the center of the bridge with the thumb out. In practice, that means a ball you switch on shouldn’t have an extra balance hole. Many bowlers keep a separate three-hole spare ball instead.

Getting Started

If you’re switching to two-handed bowling:

  1. Learn the approach and release on a ball you already have, or on a house ball without using the thumb.
  2. Once the release is repeatable, have a pro shop measure your new PAP and finger fit.
  3. Start with a moderate layout on a predictable ball, then adjust future balls based on how it reacts.
  4. Keep any three-hole ball you plan to use for spares legal for both grips, or keep it purely one-handed.

The complete guide to drilling and layouts

Bowling Ball Drilling Layouts: Pin Placement and Hole Positions Explained
Read the guide

Keep exploring

Guides from other topics

All topics →